By now you must have come across patches that just dont sound that good
or even worse. There is a simple reason, there are just to many parameters
that might not fit your setup but are perfect in the original creators setup.
For example the OUTPUT LEVEL , in most cases its very low, but in some setups
its set at 100% and the volume level is set somewhere else on the ME-90.
And thats just one example ( passive or active pickups also make a huge difference ).
Alway's, when it sounds bad, try to understand the reason, find the right adjustments
and learn from the patch.
what does a .tsl file look like ?
Example of a .tsl file, its just a text file.
{"name":"ALLAt12","formatRev":"0002","device":"ME-90","data":[[{"memo":"","paramSet":{"PATCH%COM":["41","4C","4C","41","74","31","32","20","20","20","20","20","20","20","20","20"],"PATCH%COMP":["00","07","05","32","32","32"],"PATCH%ODDS":["00","02","00","32","32","32"],"PATCH%PREAMP":["00","00","03","32","32","32","32","34","00"],"PATCH%MOD":["00","03","00","06","0E","32","32","32"],"PATCH%EQFX2":["00","05","00","32","32","32","32"],"PATCH%DLY":["00","00","00","06","0E","31","32","32"],"PATCH%REV":["00","00","00"],"PATCH%PDLFX":["00","00"],"PATCH%NS":["1E"],"PATCH%CTL":["00","00","00","01","01","00","01","01","01","00","00","00","00","00","00"],"PATCH%SNDRTN":["01"]}}
With this in mind lets make a reference sheet that you could use to fill in
your patch settings :
tsl reverence sheet --
Code: Select all
Patch Name [ ]
COMP/FX1 [ ] / SUSTAIN / ATTACK / LEVEL
/SENS/-1OCT /TONE/-2OCT/DEPTH /PEAK/DIRECT
/LOW/PITCH [ ] /HIGH/PITCH [ ] /LEVEL/FALLTIME [ ]
ODDS [ ] / DRIVE [ ] / TONE [ ] / LEVEL [ ]
PREAMP [ ] / GAIN [ ] / BASS [ ] / MIDDLE [ ] / TREBLE [ ] / LEVEL [ ]
MOD [ ] / RATE/KEY [ ] / DEPTH/HARMONY [ ] / E.LEVEL/RESONANCE [ ]
MOD [ ] / UPPER [ ] / LOWER [ ] / D.LEVEL [ ]
EQFX2 [ ] / MODE [ ] / RATE/TIME [ ] / DEPTH/FB [ ] / LEVEL [ ]
EQFX2 [ ] / BASS [ ] / MIDDLE [ ] / TREBLE [ ] / LEVEL [ ]
DLY [ ] / TIME [ ] / FEEDBACK [ ] / E.LEVEL [ ]
REV [ ] / ROOM [ ] / HALL [ ] / SPRING [ ]
PDLFX [ ] / push down to activate
NS [ ] [ ]
CTL [ ] [ ]
SNDRTN [ ] ( send and return on the unit back )
OUTPUT LEVEL [ ] ( for my presets this is at 100% )
IR [ ]
Gt.AMP * ON [ ]
INTO FRONT OF AMP [ ] / INTO FXLOOP OF AMP [ ]
OUTPUT TO DAW USB [ ] / OUTPUT TO OTHER USB INPUT DEVICE [ ]
OUTPUT TO 3.5 jack speaker [ ] / 4 CABLE METHOD [ ]
PRESS EDIT&HOLD: turn knob to see actual setting > 90 < ( example )
RECTI STACK / 8-BEND / MUFF FUZZ / OVERTONE are all No 11 and can
be replaced with other effects in boss tone studio.
( Effect Chain )
PEDALFX>COMP/FX1>OD/DS>SEND/RETURN>PREAMP>NS>FOOT>VOLUME>MOD>EQ/FX2>DELAY>REVERB
I also use this image printed and laminated so i can fill in settings
- BossME90padC.jpeg (246.02 KiB) Viewed 3303 times